diff options
Diffstat (limited to 'keyboards/atomic')
| -rw-r--r-- | keyboards/atomic/Makefile | 72 | ||||
| -rw-r--r-- | keyboards/atomic/keymaps/pvc/keymap.c | 32 | ||||
| -rw-r--r-- | keyboards/atomic/readme.md | 7 | ||||
| -rw-r--r-- | keyboards/atomic/rules.mk | 69 |
4 files changed, 97 insertions, 83 deletions
diff --git a/keyboards/atomic/Makefile b/keyboards/atomic/Makefile index 08e9205cbf..4e2a6f00fd 100644 --- a/keyboards/atomic/Makefile +++ b/keyboards/atomic/Makefile @@ -1,73 +1,3 @@ - - -# MCU name -#MCU = at90usb1287 -MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - -# Build Options -# change to "no" to disable the options, or define them in the Makefile in -# the appropriate keymap folder that will get included automatically -# -BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) -EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) -CONSOLE_ENABLE ?= no # Console for debug(+400) -COMMAND_ENABLE ?= yes # Commands for debug and configuration -NKRO_ENABLE ?= no # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality -MIDI_ENABLE ?= no # MIDI controls -AUDIO_ENABLE ?= no # Audio output on port C6 -UNICODE_ENABLE ?= no # Unicode -BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID -RGBLIGHT_ENABLE ?= no # Enable WS2812 RGB underlight. Do not enable this with audio at the same time. - -# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE -SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend - -ifndef QUANTUM_DIR +ifndef MAKEFILE_INCLUDED include ../../Makefile endif
\ No newline at end of file diff --git a/keyboards/atomic/keymaps/pvc/keymap.c b/keyboards/atomic/keymaps/pvc/keymap.c index f16ec8a6ec..b02e89d2c7 100644 --- a/keyboards/atomic/keymaps/pvc/keymap.c +++ b/keyboards/atomic/keymaps/pvc/keymap.c @@ -154,7 +154,7 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { /* UPPER * .---------------------------------------------------------------------------------------------------------------------- 2u ------------. - * | PRINT | XXXXXX | XXXXXX | XXXXXX | XXXXXX | XXXXXX | XXXXXX | NUM LK | / | * | | NUM LK | SCR LK | XXXXXX . PAUSE | + * | PRINT | BR TOG | BR SP+ | BR SP- | BR RST | XXXXXX | XXXXXX | NUM LK | / | * | | NUM LK | SCR LK | XXXXXX . PAUSE | * |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+-----------------| * | | F1 | F2 | F3 | F4 | | | 7 | 8 | 9 | - | | | | INS | * |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+- 2u ------------+--------| @@ -180,9 +180,9 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { * |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+-----------------| * | | $ | { | [ | ( | % | # | ) | ] | } | @ | | | | INS | * |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+- 2u ------------+--------| - * | | ^ | * | + | - | ; | : | _ | ' | " | ` | | XXXXXX . | HOME | + * | | ^ | * | + | - | / | \ | _ | ' | " | ` | | XXXXXX . | HOME | * |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+- 2u ---------------------+--------| - * | | | | & | ! | ~ | / | \ | = | < | > | ? | XXXXXX . | | END | + * | | | | & | ! | ~ | ; | : | = | < | > | ? | XXXXXX . | | END | * |--------+--------+--------+--------+--------+- 2u ------------+--------+--------+--------+--------+-----------------+--------+--------| * | | | | | | | | | | | | | | | * '--------------------------------------------------------------------------------------------------------------------------------------' @@ -191,16 +191,30 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { [LAYER_LOWER] = { // LOWER { _______, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, ________________ }, { _______, KC_DLR, KC_LCBR, KC_LBRC, KC_LPRN, KC_PERC, KC_HASH, KC_RPRN, KC_RBRC, KC_RCBR, KC_AT, _______, _______, _______, KC_INS }, - { _______, KC_CIRC, KC_ASTR, KC_PPLS, KC_PMNS, KC_SCLN, KC_COLN, KC_UNDS, KC_QUOT, KC_DQT, KC_GRV, _______, ________________, KC_HOME }, - { _______, KC_PIPE, KC_AMPR, KC_EXLM, KC_TILD, KC_SLSH, KC_BSLS, KC_EQL, KC_LT, KC_GT, KC_QUES, ________________, _______, KC_END }, + { _______, KC_CIRC, KC_ASTR, KC_PPLS, KC_PMNS, KC_SLSH, KC_BSLS, KC_UNDS, KC_QUOT, KC_DQT, KC_GRV, _______, ________________, KC_HOME }, + { _______, KC_PIPE, KC_AMPR, KC_EXLM, KC_TILD, KC_SCLN, KC_COLN, KC_EQL, KC_LT, KC_GT, KC_QUES, ________________, _______, KC_END }, { _______, _______, _______, _______, _______, ________________, _______, _______, _______, _______, _______, _______, _______, _______ }, }, +/* FUNCTION + * .---------------------------------------------------------------------------------------------------------------------- 2u ------------. + * | NUM LK | | | | | | | | | | | | | XXXXXX . | + * |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+-----------------| + * | SCR LK | F13 | F14 | F15 | F16 | | | | | | | | | | | + * |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+- 2u ------------+--------| + * | CAP LK | F17 | F18 | F19 | F20 | | | | | | | | XXXXXX . | | + * |--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+--------+- 2u ---------------------+--------| + * | | F21 | F22 | F23 | F24 | | | | | | | XXXXXX . | VOL UP | MUTE | + * |--------+--------+--------+--------+--------+- 2u ------------+--------+--------+--------+--------+-----------------+--------+--------| + * | | | | | | PLAY/PAUSE | | | | | | PTRACK | VOL DN | NTRACK | + * '--------------------------------------------------------------------------------------------------------------------------------------' + */ + [LAYER_FUNCTION] = { // FUNCTION - { KC_NLCK, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, ________________ }, - { KC_SLCK, KC_F13, KC_F14, KC_F15, KC_F16, KC_F17, KC_F18, KC_F19, KC_F20, KC_F21, KC_F22, KC_F23, KC_F24, _______, KC_PAUS }, - { KC_CAPS, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, ________________, KC_PSCR }, - { _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, ________________, KC_VOLU, KC_MUTE }, + { KC_NLCK, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXXXXXXXXXXX }, + { KC_SLCK, KC_F13, KC_F14, KC_F15, KC_F16, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX }, + { KC_CAPS, KC_F17, KC_F18, KC_F19, KC_F20, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXXXXXXXXXXX, XXXXXXX }, + { _______, KC_F21, KC_F22, KC_F23, KC_F24, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, ________________, KC_VOLU, KC_MUTE }, { _______, _______, _______, _______, _______, KC_MPLY, KC_MPLY, _______, _______, _______, _______, _______, KC_MPRV, KC_VOLD, KC_MNXT }, }, diff --git a/keyboards/atomic/readme.md b/keyboards/atomic/readme.md index ab1e7ba1ff..674dcf113b 100644 --- a/keyboards/atomic/readme.md +++ b/keyboards/atomic/readme.md @@ -13,13 +13,14 @@ Download or clone the whole firmware and navigate to the keyboards/atomic folder Depending on which keymap you would like to use, you will have to compile slightly differently. ### Default -To build with the default keymap, simply run `make`. +To build with the default keymap, simply run `make default`. ### Other Keymaps Several version of keymap are available in advance but you are recommended to define your favorite layout yourself. To define your own keymap create a file in the keymaps folder named `<name>.c` and see keymap document (you can find in top readme.md) and existent keymap files. -To build the firmware binary hex file with a keymap just do `make` with `KEYMAP` option like: +To build the firmware binary hex file with a keymap just do `make` with a keymap like this: + ``` -$ make KEYMAP=[default|jack|<name>] +$ make [default|jack|<name>] ``` Keymaps follow the format **__\<name\>.c__** and are stored in the `keymaps` folder. diff --git a/keyboards/atomic/rules.mk b/keyboards/atomic/rules.mk new file mode 100644 index 0000000000..d0f3a3a1c0 --- /dev/null +++ b/keyboards/atomic/rules.mk @@ -0,0 +1,69 @@ + + +# MCU name +#MCU = at90usb1287 +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=4096 + +# Build Options +# change to "no" to disable the options, or define them in the Makefile in +# the appropriate keymap folder that will get included automatically +# +BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) +EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) +CONSOLE_ENABLE ?= no # Console for debug(+400) +COMMAND_ENABLE ?= yes # Commands for debug and configuration +NKRO_ENABLE ?= no # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality +MIDI_ENABLE ?= no # MIDI controls +AUDIO_ENABLE ?= no # Audio output on port C6 +UNICODE_ENABLE ?= no # Unicode +BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID +RGBLIGHT_ENABLE ?= no # Enable WS2812 RGB underlight. Do not enable this with audio at the same time. + +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend
\ No newline at end of file |