Sol Rev 2 Keyboard (#6389)

* Basic Rev 2 implementation

* Updated LED defines and added Extra encoder support

* Fixed rgb pin assignment

* Physically accurate LED positions

* Single Color Band scrolling left to right effects

* Spirals, Pinwheels, and Documentation....Oh My!

* Spiral effect band thickness adjustments

* Fixing animation spin directions

* Full hand LED positions

* Basic Rev 2 implementation

Updated LED defines and added Extra encoder support

Fixed rgb pin assignment

Physically accurate LED positions

Full hand LED positions

Moving rev2 folder

* RGB Center Point LED position update

* Fixing led config commas

* Fixing led config commas

* fix enter key

* fix enter

* Small changes to default

* update default

* typo fix

* update default

* Fixing defines & led config, turned full hand & extra encoders into rules.mk feature

* Refactored rules.mk to have a post_rules.mk

* Forgot to offset the matrix to led map due to the edge led additions

* Updated LED flags and fixed my keymap

* Update keymap.c

include speed controls for RGB

* Fixing more rules.mk and adding keymap like encoders functionality

* Sol Rev 2 Implementation

* Minor fixes

* Keymap fixes

* Fix Colemak, add lock keys

1 files changed, 1 insertions, 41 deletions

diff --git a/keyboards/rgbkb/sol/rules.mk b/keyboards/rgbkb/sol/rules.mk
index a3dcfc2903..3be8f0b229 100644
--- a/keyboards/rgbkb/sol/rules.mk
+++ b/keyboards/rgbkb/sol/rules.mk
@@ -2,41 +2,15 @@
 MCU = atmega32u4
 
 # Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
 F_CPU = 16000000
 
-#
-# LUFA specific
-#
 # Target architecture (see library "Board Types" documentation).
 ARCH = AVR8
 
 # Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
 F_USB = $(F_CPU)
 
 # Bootloader
-#     This definition is optional, and if your keyboard supports multiple bootloaders of
-#     different sizes, comment this out, and the correct address will be loaded
-#     automatically (+60). See bootloader.mk for all options.
 BOOTLOADER = qmk-dfu
 
 # Interrupt driven control endpoint task(+60)
@@ -48,18 +22,4 @@ OPT_DEFS += -DOLED_FONT_H=\"common/glcdfont.c\"
 SPLIT_KEYBOARD = yes
 ENCODER_ENABLE = yes
 
-# Build Options
-#   change to "no" to disable the options, or define them in the Makefile in
-#   the appropriate keymap folder that will get included automatically
-#
-BOOTMAGIC_ENABLE = no       # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE = yes       # Mouse keys(+4700)
-EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
-CONSOLE_ENABLE = no         # Console for debug(+400)
-COMMAND_ENABLE = yes        # Commands for debug and configuration
-NKRO_ENABLE = no            # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-UNICODE_ENABLE = no         # Unicode
-BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
-RGBLIGHT_ENABLE = yes       # Enable WS2812 RGB underlight.  Do not enable this with audio at the same time.
-
-DEFAULT_FOLDER = rgbkb/sol/rev1
+DEFAULT_FOLDER = rgbkb/sol/rev2