summaryrefslogtreecommitdiff
path: root/keyboards/planck
diff options
context:
space:
mode:
Diffstat (limited to 'keyboards/planck')
-rw-r--r--keyboards/planck/Makefile71
-rw-r--r--keyboards/planck/readme.md8
-rw-r--r--keyboards/planck/rev3/Makefile4
-rw-r--r--keyboards/planck/rev3/rules.mk5
-rw-r--r--keyboards/planck/rev4/Makefile4
-rw-r--r--keyboards/planck/rev4/rules.mk5
-rw-r--r--keyboards/planck/rules.mk67
7 files changed, 85 insertions, 79 deletions
diff --git a/keyboards/planck/Makefile b/keyboards/planck/Makefile
index 23944f92ea..7d49c5ef96 100644
--- a/keyboards/planck/Makefile
+++ b/keyboards/planck/Makefile
@@ -1,74 +1,5 @@
-
SUBPROJECT_DEFAULT = rev4
-# MCU name
-#MCU = at90usb1287
-MCU = atmega32u4
-
-# Processor frequency.
-# This will define a symbol, F_CPU, in all source code files equal to the
-# processor frequency in Hz. You can then use this symbol in your source code to
-# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-# automatically to create a 32-bit value in your source code.
-#
-# This will be an integer division of F_USB below, as it is sourced by
-# F_USB after it has run through any CPU prescalers. Note that this value
-# does not *change* the processor frequency - it should merely be updated to
-# reflect the processor speed set externally so that the code can use accurate
-# software delays.
-F_CPU = 16000000
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-# This will define a symbol, F_USB, in all source code files equal to the
-# input clock frequency (before any prescaling is performed) in Hz. This value may
-# differ from F_CPU if prescaling is used on the latter, and is required as the
-# raw input clock is fed directly to the PLL sections of the AVR for high speed
-# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-# at the end, this will be done automatically to create a 32-bit value in your
-# source code.
-#
-# If no clock division is performed on the input clock inside the AVR (via the
-# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-# Teensy halfKay 512
-# Teensy++ halfKay 1024
-# Atmel DFU loader 4096
-# LUFA bootloader 4096
-# USBaspLoader 2048
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-# Build Options
-# change to "no" to disable the options, or define them in the Makefile in
-# the appropriate keymap folder that will get included automatically
-#
-BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700)
-EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450)
-CONSOLE_ENABLE ?= no # Console for debug(+400)
-COMMAND_ENABLE ?= yes # Commands for debug and configuration
-NKRO_ENABLE ?= no # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality
-MIDI_ENABLE ?= no # MIDI controls
-AUDIO_ENABLE ?= no # Audio output on port C6
-UNICODE_ENABLE ?= no # Unicode
-BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID
-RGBLIGHT_ENABLE ?= no # Enable WS2812 RGB underlight. Do not enable this with audio at the same time.
-
-# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
-SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend
-
-ifndef QUANTUM_DIR
+ifndef MAKEFILE_INCLUDED
include ../../Makefile
endif \ No newline at end of file
diff --git a/keyboards/planck/readme.md b/keyboards/planck/readme.md
index f89fdeb931..4b24a690e0 100644
--- a/keyboards/planck/readme.md
+++ b/keyboards/planck/readme.md
@@ -13,15 +13,17 @@ Download or clone the whole firmware and navigate to the keyboards/planck folder
Depending on which keymap you would like to use, you will have to compile slightly differently.
### Default
-To build with the default keymap, simply run `make`.
+To build with the default keymap, simply run `make default`.
### Other Keymaps
Several version of keymap are available in advance but you are recommended to define your favorite layout yourself. To define your own keymap create file named `<name>.c` in the keymaps folder, and see keymap document (you can find in top readme.md) and existent keymap files.
-To build the firmware binary hex file with a keymap just do `make` with `KEYMAP` option like:
+To build the firmware binary hex file with a keymap just do `make` with a keymap like this:
+
```
-$ make KEYMAP=[default|jack|<name>]
+$ make [default|jack|<name>]
```
+
Keymaps follow the format **__\<name\>.c__** and are stored in the `keymaps` folder.
### Notable forks (which some of the keymap files are from)
diff --git a/keyboards/planck/rev3/Makefile b/keyboards/planck/rev3/Makefile
index 3ed1445e43..191c6bb664 100644
--- a/keyboards/planck/rev3/Makefile
+++ b/keyboards/planck/rev3/Makefile
@@ -1,5 +1,3 @@
-AUDIO_ENABLE ?= no # Audio output on port C6
-
-ifndef QUANTUM_DIR
+ifndef MAKEFILE_INCLUDED
include ../../../Makefile
endif \ No newline at end of file
diff --git a/keyboards/planck/rev3/rules.mk b/keyboards/planck/rev3/rules.mk
new file mode 100644
index 0000000000..3ed1445e43
--- /dev/null
+++ b/keyboards/planck/rev3/rules.mk
@@ -0,0 +1,5 @@
+AUDIO_ENABLE ?= no # Audio output on port C6
+
+ifndef QUANTUM_DIR
+ include ../../../Makefile
+endif \ No newline at end of file
diff --git a/keyboards/planck/rev4/Makefile b/keyboards/planck/rev4/Makefile
index ed09f85a4d..191c6bb664 100644
--- a/keyboards/planck/rev4/Makefile
+++ b/keyboards/planck/rev4/Makefile
@@ -1,5 +1,3 @@
-AUDIO_ENABLE ?= yes # Audio output on port C6
-
-ifndef QUANTUM_DIR
+ifndef MAKEFILE_INCLUDED
include ../../../Makefile
endif \ No newline at end of file
diff --git a/keyboards/planck/rev4/rules.mk b/keyboards/planck/rev4/rules.mk
new file mode 100644
index 0000000000..ed09f85a4d
--- /dev/null
+++ b/keyboards/planck/rev4/rules.mk
@@ -0,0 +1,5 @@
+AUDIO_ENABLE ?= yes # Audio output on port C6
+
+ifndef QUANTUM_DIR
+ include ../../../Makefile
+endif \ No newline at end of file
diff --git a/keyboards/planck/rules.mk b/keyboards/planck/rules.mk
new file mode 100644
index 0000000000..25db53a315
--- /dev/null
+++ b/keyboards/planck/rules.mk
@@ -0,0 +1,67 @@
+# MCU name
+#MCU = at90usb1287
+MCU = atmega32u4
+
+# Processor frequency.
+# This will define a symbol, F_CPU, in all source code files equal to the
+# processor frequency in Hz. You can then use this symbol in your source code to
+# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+# automatically to create a 32-bit value in your source code.
+#
+# This will be an integer division of F_USB below, as it is sourced by
+# F_USB after it has run through any CPU prescalers. Note that this value
+# does not *change* the processor frequency - it should merely be updated to
+# reflect the processor speed set externally so that the code can use accurate
+# software delays.
+F_CPU = 16000000
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+# This will define a symbol, F_USB, in all source code files equal to the
+# input clock frequency (before any prescaling is performed) in Hz. This value may
+# differ from F_CPU if prescaling is used on the latter, and is required as the
+# raw input clock is fed directly to the PLL sections of the AVR for high speed
+# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+# at the end, this will be done automatically to create a 32-bit value in your
+# source code.
+#
+# If no clock division is performed on the input clock inside the AVR (via the
+# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Boot Section Size in *bytes*
+# Teensy halfKay 512
+# Teensy++ halfKay 1024
+# Atmel DFU loader 4096
+# LUFA bootloader 4096
+# USBaspLoader 2048
+OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+# Build Options
+# change to "no" to disable the options, or define them in the Makefile in
+# the appropriate keymap folder that will get included automatically
+#
+BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700)
+EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450)
+CONSOLE_ENABLE ?= no # Console for debug(+400)
+COMMAND_ENABLE ?= yes # Commands for debug and configuration
+NKRO_ENABLE ?= no # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality
+MIDI_ENABLE ?= no # MIDI controls
+AUDIO_ENABLE ?= no # Audio output on port C6
+UNICODE_ENABLE ?= no # Unicode
+BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID
+RGBLIGHT_ENABLE ?= no # Enable WS2812 RGB underlight. Do not enable this with audio at the same time.
+
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend \ No newline at end of file