summaryrefslogtreecommitdiff
diff options
context:
space:
mode:
-rw-r--r--keyboards/jj50/README.md79
-rw-r--r--keyboards/jj50/config.h54
-rw-r--r--keyboards/jj50/i2c.c104
-rw-r--r--keyboards/jj50/i2c.h25
-rw-r--r--keyboards/jj50/jj50.c45
-rw-r--r--keyboards/jj50/jj50.h50
-rw-r--r--keyboards/jj50/keymaps/default/keymap.c96
-rw-r--r--keyboards/jj50/matrix.c106
-rw-r--r--keyboards/jj50/program74
-rw-r--r--keyboards/jj50/rules.mk51
-rw-r--r--keyboards/jj50/usbconfig.h396
-rw-r--r--keyboards/ymd96/keymaps/JJ50/keymap.c96
-rw-r--r--keyboards/ymd96/ymd96.h13
13 files changed, 1189 insertions, 0 deletions
diff --git a/keyboards/jj50/README.md b/keyboards/jj50/README.md
new file mode 100644
index 0000000000..39cfc69ca0
--- /dev/null
+++ b/keyboards/jj50/README.md
@@ -0,0 +1,79 @@
+JJ50
+==========================
+
+This is a port of the QMK firmware for boards that are based on the
+ps2avrGB firmware, like the [ps2avrGB keyboard] (https://www.keyclack.com/product/gb-ps2avrgb/), for use on the JJ50, a preonic-like board.
+
+Most of the code was taken and amended from YMD96, which in itself was taken from ps2avrGB and amended by Andrew Novak.
+
+Note that this is a complete replacement for the firmware, so you won't be
+using Bootmapper Client to change any keyboard settings, since not all the
+USB report options are supported.
+
+Hardware Supported: JJ50 with the ATmega32a chip.
+Hardware Availability: The JJ50 PCB is available from kprepublic on AliExpress and suchlike.
+
+
+## Installing and Building
+
+Make example for this keyboard (after setting up your build environment):
+
+```
+$ make jj50:default:program
+```
+It should detect the keyboard and set it to bootloader mode automatically, prior to flashing firmware.
+
+See [build environment setup](https://docs.qmk.fm/build_environment_setup.html) then the [make instructions](https://docs.qmk.fm/make_instructions.html) for more information.
+
+Note that this is a complete replacement for the firmware, so you won't be
+using Bootmapper Client to change any keyboard settings, since not all the
+USB report options are supported.
+In addition you may need the AVR toolchain and `bootloadHID` for flashing:
+
+```
+$ brew cask install crosspack-avr
+$ brew install --HEAD https://raw.githubusercontent.com/robertgzr/homebrew-tap/master/bootloadhid.rb
+```
+
+In order to use the `./program` script, which can reboot the board into
+the bootloader, you'll need Python 2 with PyUSB installed:
+
+```
+$ pip install pyusb
+```
+
+If you prefer, you can just build it and flash the firmware directly with
+`bootloadHID` if you boot the board while holding down `Backspace` (`key below top right key`) to keep it
+in the bootloader:
+
+```
+$ make jj50
+$ bootloadHID -r jj50_default.hex
+```
+I dont use windows personally, but the following is from ymd96 regarding flashing the atmega32a:
+
+Since the JJ50 uses an ATmega32a chip instead of the 32u4, you need to download [HIDBootFlash v.1.0](http://vusb.wikidot.com/project:hidbootflash) for Windows. If anyone knows of a Linux/Mac bootflasher that works, edit this readme!
+On Windows, I use [MINGw](http://www.mingw.org/) to compile the keymaps. On Linux or OSX you can simply use the terminal.
+
+Once you have those two pieces of software:
+Build the keyboard with
+```
+$ make jj50:default
+```
+If you make your own layout, change the `default` word to whatever your layout is.
+
+And flash the compiled hex file with `HIDBootFlash`. Simply put the board in flashing mode by plugging it in while holding the key below the top right key, and click `find device`. Then you can specify the .hex file and flash it to the device.
+
+
+## Troubleshooting
+
+1. Try plugging the board in while pressing `Backspace` (`Key below the top right key`). This will force it to boot only the bootloader without loading the firmware. Once this is done, just reflash the board with the original firmware.
+2. Sometimes USB hubs can act weird, so try connecting the board directly to your computer or plugging/unplugging the USB hub.
+3. If you get an error such as "Resource Unavailable" when attemting to flash on Linux, you may want to compile and run `tools/usb_detach.c`. See `tools/README.md` for more info.
+4. I was occasionally finding that I wasn't flashing changes that I was making to my keymap. If that happens, simply force rebuild by making with:
+```
+$ make -B jj50:default:program
+```
+
+
+
diff --git a/keyboards/jj50/config.h b/keyboards/jj50/config.h
new file mode 100644
index 0000000000..240732594d
--- /dev/null
+++ b/keyboards/jj50/config.h
@@ -0,0 +1,54 @@
+/*
+Base Copyright 2017 Luiz Ribeiro <luizribeiro@gmail.com>
+Modified 2017 Andrew Novak <ndrw.nvk@gmail.com>
+Modified 2018 Wayne Jones (WarmCatUK) <waynekjones@gmail.com>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program. If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#ifndef CONFIG_H
+#define CONFIG_H
+
+#include "config_common.h"
+
+#define VENDOR_ID 0x20A0
+#define PRODUCT_ID 0x422D
+// TODO: share these strings with usbconfig.h
+// Edit usbconfig.h to change these.
+#define MANUFACTURER kprepublic
+#define PRODUCT jj50
+#define DESCRIPTION Preonic-like clone
+
+/* matrix size */
+#define MATRIX_ROWS 8
+#define MATRIX_COLS 15
+#define DIODE_DIRECTION ROW2COL
+
+#define BACKLIGHT_PIN D4
+#define BACKLIGHT_LEVELS 3
+
+//#define RGB_DI_PIN C0
+#define RGBLED_NUM 5
+#define RGBLIGHT_ANIMATIONS
+#define RGBLIGHT_HUE_STEP 12
+#define RGBLIGHT_SAT_STEP 15
+#define RGBLIGHT_VAL_STEP 18
+
+#define NO_UART 1
+#define BOOTLOADHID_BOOTLOADER 1
+
+/* key combination for command */
+#define IS_COMMAND() (keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)))
+
+#endif
diff --git a/keyboards/jj50/i2c.c b/keyboards/jj50/i2c.c
new file mode 100644
index 0000000000..c27f3e3d17
--- /dev/null
+++ b/keyboards/jj50/i2c.c
@@ -0,0 +1,104 @@
+/*
+Copyright 2016 Luiz Ribeiro <luizribeiro@gmail.com>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program. If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#include <avr/io.h>
+#include <util/twi.h>
+
+#include "i2c.h"
+
+void i2c_set_bitrate(uint16_t bitrate_khz) {
+ uint8_t bitrate_div = ((F_CPU / 1000l) / bitrate_khz);
+ if (bitrate_div >= 16) {
+ bitrate_div = (bitrate_div - 16) / 2;
+ }
+ TWBR = bitrate_div;
+}
+
+void i2c_init(void) {
+ // set pull-up resistors on I2C bus pins
+ PORTC |= 0b11;
+
+ i2c_set_bitrate(400);
+
+ // enable TWI (two-wire interface)
+ TWCR |= (1 << TWEN);
+
+ // enable TWI interrupt and slave address ACK
+ TWCR |= (1 << TWIE);
+ TWCR |= (1 << TWEA);
+}
+
+uint8_t i2c_start(uint8_t address) {
+ // reset TWI control register
+ TWCR = 0;
+
+ // begin transmission and wait for it to end
+ TWCR = (1<<TWINT) | (1<<TWSTA) | (1<<TWEN);
+ while (!(TWCR & (1<<TWINT)));
+
+ // check if the start condition was successfully transmitted
+ if ((TWSR & 0xF8) != TW_START) {
+ return 1;
+ }
+
+ // transmit address and wait
+ TWDR = address;
+ TWCR = (1<<TWINT) | (1<<TWEN);
+ while (!(TWCR & (1<<TWINT)));
+
+ // check if the device has acknowledged the READ / WRITE mode
+ uint8_t twst = TW_STATUS & 0xF8;
+ if ((twst != TW_MT_SLA_ACK) && (twst != TW_MR_SLA_ACK)) {
+ return 1;
+ }
+
+ return 0;
+}
+
+void i2c_stop(void) {
+ TWCR = (1<<TWINT) | (1<<TWEN) | (1<<TWSTO);
+}
+
+uint8_t i2c_write(uint8_t data) {
+ TWDR = data;
+
+ // transmit data and wait
+ TWCR = (1<<TWINT) | (1<<TWEN);
+ while (!(TWCR & (1<<TWINT)));
+
+ if ((TWSR & 0xF8) != TW_MT_DATA_ACK) {
+ return 1;
+ }
+
+ return 0;
+}
+
+uint8_t i2c_send(uint8_t address, uint8_t *data, uint16_t length) {
+ if (i2c_start(address)) {
+ return 1;
+ }
+
+ for (uint16_t i = 0; i < length; i++) {
+ if (i2c_write(data[i])) {
+ return 1;
+ }
+ }
+
+ i2c_stop();
+
+ return 0;
+}
diff --git a/keyboards/jj50/i2c.h b/keyboards/jj50/i2c.h
new file mode 100644
index 0000000000..27c9d3d050
--- /dev/null
+++ b/keyboards/jj50/i2c.h
@@ -0,0 +1,25 @@
+/*
+Copyright 2016 Luiz Ribeiro <luizribeiro@gmail.com>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program. If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#ifndef __I2C_H__
+#define __I2C_H__
+
+void i2c_init(void);
+void i2c_set_bitrate(uint16_t bitrate_khz);
+uint8_t i2c_send(uint8_t address, uint8_t *data, uint16_t length);
+
+#endif
diff --git a/keyboards/jj50/jj50.c b/keyboards/jj50/jj50.c
new file mode 100644
index 0000000000..a75b12c4ea
--- /dev/null
+++ b/keyboards/jj50/jj50.c
@@ -0,0 +1,45 @@
+/*
+Copyright 2017 Luiz Ribeiro <luizribeiro@gmail.com>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program. If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#include "jj50.h"
+#include "rgblight.h"
+
+#include <avr/pgmspace.h>
+
+#include "action_layer.h"
+#include "i2c.h"
+#include "quantum.h"
+
+extern rgblight_config_t rgblight_config;
+
+void rgblight_set(void) {
+ if (!rgblight_config.enable) {
+ for (uint8_t i = 0; i < RGBLED_NUM; i++) {
+ led[i].r = 0;
+ led[i].g = 0;
+ led[i].b = 0;
+ }
+ }
+
+ i2c_init();
+ i2c_send(0xb0, (uint8_t*)led, 3 * RGBLED_NUM);
+}
+
+__attribute__ ((weak))
+void matrix_scan_user(void) {
+ rgblight_task();
+}
diff --git a/keyboards/jj50/jj50.h b/keyboards/jj50/jj50.h
new file mode 100644
index 0000000000..09664f77f6
--- /dev/null
+++ b/keyboards/jj50/jj50.h
@@ -0,0 +1,50 @@
+/*
+Base Copyright 2017 Luiz Ribeiro <luizribeiro@gmail.com>
+Modified 2017 Andrew Novak <ndrw.nvk@gmail.com>
+Modified 2018 Wayne Jones (WarmCatUK) <waynekjones@gmail.com>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program. If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#ifndef KEYMAP_COMMON_H
+#define KEYMAP_COMMON_H
+
+#include "quantum_keycodes.h"
+#include "keycode.h"
+#include "action.h"
+
+#define KEYMAP( \
+K011, K010, K009, K008, K004, K005, K006, K007, K003, K002, K201, K000, \
+K111, K110, K109, K108, K104, K105, K106, K107, K103, K102, K001, K100, \
+K211, K210, K209, K208, K204, K205, K206, K207, K203, K202, K101, K200, \
+K311, K310, K309, K308, K304, K305, K306, K307, K303, K302, K301, K300, \
+K411, K410, K409, K408, K404, K405, K406, K407, K403, K402, K401, K400 \
+) { \
+{ K100, K001, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, }, \
+{ K200, K101, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, }, \
+{ K000, K201, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, }, \
+{ K300, K301, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, }, \
+{ K400, K401, K402, K403, K404, K405, K406, K407, K408, K409, K410, K411 }, \
+}
+
+#endif
+
+
+
+
+
+
+
+
+
diff --git a/keyboards/jj50/keymaps/default/keymap.c b/keyboards/jj50/keymaps/default/keymap.c
new file mode 100644
index 0000000000..8a32efd0c0
--- /dev/null
+++ b/keyboards/jj50/keymaps/default/keymap.c
@@ -0,0 +1,96 @@
+/*
+Base Copyright 2017 Luiz Ribeiro <luizribeiro@gmail.com>
+Modified 2017 Andrew Novak <ndrw.nvk@gmail.com>
+Modified 2018 Wayne Jones (WarmCatUK) <waynekjones@gmail.com>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public LicensezZZ
+along with this program. If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#include "jj50.h"
+#include "action_layer.h"
+#include "rgblight.h"
+
+#define ______ KC_TRNS
+#define _DEFLT 0
+#define _RAISE 1
+#define _LOWER 2
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+
+ /* Qwerty
+ * ,-----------------------------------------------------------------------------------.
+ * | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 0 | - | = |
+ * |------+------+------+------+------+------+------+------+------+------+------+------|
+ * | Tab | Q | W | E | R | T | Y | U | I | O | P | Bksp |
+ * |------+------+------+------+------+------+------+------+------+------+------+------|
+ * | Esc | A | S | D | F | G | H | J | K | L | ; | " |
+ * |------+------+------+------+------+------+------+------+------+------+------+------|
+ * | Shift| Z | X | C | V | B | N | M | , | . | / |Enter |
+ * |------+------+------+------+------+------+------+------+------+------+------+------|
+ * | | Ctrl | Alt | GUI |Lower | Space |Raise | Left | Down | Up |Right |
+ * `-----------------------------------------------------------------------------------'
+ */
+ [_DEFLT] = KEYMAP( \
+ KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, \
+ KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_BSPC, \
+ KC_ESC, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, \
+ KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, SFT_T(KC_ENT),\
+ BL_TOGG, KC_LCTL, KC_LALT, KC_LGUI, MO(_LOWER), KC_SPC,KC_SPC, MO(_RAISE),KC_LEFT, KC_DOWN, KC_UP, KC_RGHT \
+ ),
+
+
+ /* Raise
+ * ,-----------------------------------------------------------------------------------.
+ * | F1 | F2 | F3 | F4 | F5 | F6 | F7 | F8 | F9 | F10 | F11 | F12 |
+ * |------+------+------+------+------+------+------+------+------+------+------+------|
+ * | ` | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 0 | Del |
+ * |------+------+------+------+------+------+------+------+------+------+------+------|
+ * | | | | | | | | | | [ | ] | \ |
+ * |------+------+------+------+------+------+------+------+------+------+------+------|
+ * | | | | | | | |ISO # |ISO / | PUP | PDN | |
+ * |------+------+------+------+------+------+------+------+------+------+------+------|
+ * | | | | | | | | Next | Vol- | Vol+ | Play |
+ * `-----------------------------------------------------------------------------------'
+ */
+ [_RAISE] = KEYMAP( \
+ KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, \
+ KC_GRV, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_DEL, \
+ RESET, BL_INC, RGB_SAI, _______, _______, _______, _______, _______, _______, KC_LBRC, KC_RBRC, KC_BSLS, \
+ _______, BL_DEC, _______, _______, _______, _______, _______, KC_NUHS, KC_NUBS, KC_PGUP, KC_PGDN, _______, \
+ RGB_TOG, _______, _______, _______, _______, _______, _______, _______, KC_MNXT, KC_VOLD, KC_VOLU, KC_MPLY \
+ ),
+
+
+ /* Lower
+ * ,-----------------------------------------------------------------------------------.
+ * | F1 | F2 | F3 | F4 | F5 | F6 | F7 | F8 | F9 | F10 | F11 | F12 |
+ * |------+------+------+------+------+------+------+------+------+------+------+------|
+ * | ~ | ! | @ | # | $ | % | ^ | & | * | ( | ) | Del |
+ * |------+------+------+------+------+------+------+------+------+------+------+------|
+ * | | | | | | | | | | { | } | | |
+ * |------+------+------+------+------+------+------+------+------+------+------+------|
+ * | | | | | | | |ISO ~ |ISO | | HOM | END | |
+ * |------+------+------+------+------+------+------+------+------+------+------+------|
+ * | | | | | | | | Next | Vol- | Vol+ | Play |
+ * `-----------------------------------------------------------------------------------'
+ */
+ [_LOWER] = KEYMAP( \
+ KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, \
+ KC_TILD, KC_EXLM, KC_AT, KC_HASH, KC_DLR, KC_PERC, KC_CIRC, KC_AMPR, KC_ASTR, KC_LPRN, KC_RPRN, KC_DEL, \
+ RESET, _______, _______, _______, _______, _______, _______, _______, _______, KC_LCBR, KC_RCBR, KC_PIPE, \
+ _______, _______, _______, _______, _______, _______, _______,S(KC_NUHS),S(KC_NUBS),KC_HOME, KC_END, _______, \
+ _______, _______, _______, _______, _______, _______, _______, _______, KC_MNXT, KC_VOLD, KC_VOLU, KC_MPLY \
+ )
+
+};
diff --git a/keyboards/jj50/matrix.c b/keyboards/jj50/matrix.c
new file mode 100644
index 0000000000..8f9c67fe47
--- /dev/null
+++ b/keyboards/jj50/matrix.c
@@ -0,0 +1,106 @@
+/*
+Copyright 2017 Luiz Ribeiro <luizribeiro@gmail.com>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program. If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#include <avr/io.h>
+#include <util/delay.h>
+
+#include "matrix.h"
+
+#ifndef DEBOUNCE
+# define DEBOUNCE 5
+#endif
+
+static uint8_t debouncing = DEBOUNCE;
+
+static matrix_row_t matrix[MATRIX_ROWS];
+static matrix_row_t matrix_debouncing[MATRIX_ROWS];
+
+void matrix_init(void) {
+ // all outputs for rows high
+ DDRB = 0xFF;
+ PORTB = 0xFF;
+ // all inputs for columns
+ DDRA = 0x00;
+ DDRC &= ~(0x111111<<2);
+ DDRD &= ~(1<<PIND7);
+ // all columns are pulled-up
+ PORTA = 0xFF;
+ PORTC |= (0b111111<<2);
+ //PORTD |= (1<<PIND7);
+
+ // initialize matrix state: all keys off
+ for (uint8_t row = 0; row < MATRIX_ROWS; row++) {
+ matrix[row] = 0x00;
+ matrix_debouncing[row] = 0x00;
+ }
+}
+
+void matrix_set_row_status(uint8_t row) {
+ DDRB = (1 << row);
+ PORTB = ~(1 << row);
+}
+
+uint8_t bit_reverse(uint8_t x) {
+ x = ((x >> 1) & 0x55) | ((x << 1) & 0xaa);
+ x = ((x >> 2) & 0x33) | ((x << 2) & 0xcc);
+ x = ((x >> 4) & 0x0f) | ((x << 4) & 0xf0);
+ return x;
+}
+
+uint8_t matrix_scan(void) {
+ for (uint8_t row = 0; row < MATRIX_ROWS; row++) {
+ matrix_set_row_status(row);
+ _delay_us(5);
+
+ matrix_row_t cols = (
+ // cols 0..7, PORTA 0 -> 7
+ (~PINA) & 0xFF
+ ) | (
+ // cols 8..13, PORTC 7 -> 0
+ bit_reverse((~PINC) & 0xFF) << 8
+ ) | (
+ // col 14, PORTD 7
+ ((~PIND) & (1 << PIND7)) << 7
+ );
+
+ if (matrix_debouncing[row] != cols) {
+ matrix_debouncing[row] = cols;
+ debouncing = DEBOUNCE;
+ }
+ }
+
+ if (debouncing) {
+ if (--debouncing) {
+ _delay_ms(1);
+ } else {
+ for (uint8_t i = 0; i < MATRIX_ROWS; i++) {
+ matrix[i] = matrix_debouncing[i];
+ }
+ }
+ }
+
+ matrix_scan_user();
+
+ return 1;
+}
+
+inline matrix_row_t matrix_get_row(uint8_t row) {
+ return matrix[row];
+}
+
+void matrix_print(void) {
+}
diff --git a/keyboards/jj50/program b/keyboards/jj50/program
new file mode 100644
index 0000000000..a88d9cd9b0
--- /dev/null
+++ b/keyboards/jj50/program
@@ -0,0 +1,74 @@
+#!/usr/bin/env python
+# Copyright 2017 Luiz Ribeiro <luizribeiro@gmail.com>
+#
+# This program is free software: you can redistribute it and/or modify
+# it under the terms of the GNU General Public License as published by
+# the Free Software Foundation, either version 2 of the License, or
+# (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program. If not, see <http://www.gnu.org/licenses/>.
+
+from __future__ import print_function
+
+import os
+import sys
+import time
+import usb
+
+if len(sys.argv) < 2:
+ print('Usage: %s <firmware.hex>' % sys.argv[0])
+ sys.exit(1)
+
+print('Searching for ps2avrGB... ', end='')
+
+dev = usb.core.find(idVendor=0x20A0, idProduct=0x422D)
+if dev is None:
+ raise ValueError('Device not found')
+
+print('Found', end='\n\n')
+
+print('Device Information:')
+print(' idVendor: %d (0x%04x)' % (dev.idVendor, dev.idVendor))
+print(' idProduct: %d (0x%04x)' % (dev.idProduct, dev.idProduct))
+print('Manufacturer: %s' % (dev.iManufacturer))
+print('Serial: %s' % (dev.iSerialNumber))
+print('Product: %s' % (dev.iProduct), end='\n\n')
+
+print('Transferring control to bootloader... ', end='')
+
+dev.set_configuration()
+
+request_type = usb.util.build_request_type(
+ usb.util.CTRL_OUT,
+ usb.util.CTRL_TYPE_CLASS,
+ usb.util.CTRL_RECIPIENT_DEVICE)
+
+USBRQ_HID_SET_REPORT = 0x09
+HID_REPORT_OPTION = 0x0301
+
+
+try:
+ dev.ctrl_transfer(
+ request_type,
+ USBRQ_HID_SET_REPORT,
+ HID_REPORT_OPTION,
+ 0,
+ [0, 0, 0xFF] + [0] * 5
+ )
+except usb.core.USBError:
+ # for some reason I keep getting USBError, but it works!
+ pass
+
+# wait a bit until bootloader starts up
+time.sleep(2)
+
+print('OK')
+print('Programming...')
+if os.system('bootloadHID -r "%s"' % sys.argv[1]) == 0:
+ print('\nDone!')
diff --git a/keyboards/jj50/rules.mk b/keyboards/jj50/rules.mk
new file mode 100644
index 0000000000..1b7826e505
--- /dev/null
+++ b/keyboards/jj50/rules.mk
@@ -0,0 +1,51 @@
+# Copyright 2017 Luiz Ribeiro <luizribeiro@gmail.com>
+# Modified 2018 Wayne Jones (WarmCatUK) <waynekjones@gmail.com>
+
+# This program is free software: you can redistribute it and/or modify
+# it under the terms of the GNU General Public License as published by
+# the Free Software Foundation, either version 2 of the License, or
+# (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program. If not, see <http://www.gnu.org/licenses/>.
+
+# MCU name
+MCU = atmega32a
+PROTOCOL = VUSB
+
+# unsupported features for now
+NO_UART = yes
+NO_SUSPEND_POWER_DOWN = yes
+
+# processor frequency
+F_CPU = 12000000
+
+# Bootloader
+# This definition is optional, and if your keyboard supports multiple bootloaders of
+# different sizes, comment this out, and the correct address will be loaded
+# automatically (+60). See bootloader.mk for all options.
+BOOTLOADER = bootloadHID
+
+# build options
+BOOTMAGIC_ENABLE = yes
+MOUSEKEY_ENABLE = no
+EXTRAKEY_ENABLE = yes
+CONSOLE_ENABLE = no
+COMMAND_ENABLE = no
+BACKLIGHT_ENABLE = yes
+RGBLIGHT_ENABLE = yes
+RGBLIGHT_CUSTOM_DRIVER = yes
+
+OPT_DEFS = -DDEBUG_LEVEL=0
+
+# custom matrix setup
+CUSTOM_MATRIX = yes
+SRC = matrix.c i2c.c
+
+# programming options
+PROGRAM_CMD = ./keyboards/ps2avrGB/program $(TARGET).hex
diff --git a/keyboards/jj50/usbconfig.h b/keyboards/jj50/usbconfig.h
new file mode 100644
index 0000000000..d2d848fcdc
--- /dev/null
+++ b/keyboards/jj50/usbconfig.h
@@ -0,0 +1,396 @@
+/* Name: usbconfig.h
+ * Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
+ * Author: Christian Starkjohann
+ * Creation Date: 2005-04-01
+ * Tabsize: 4
+ * Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
+ * License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
+ * This Revision: $Id: usbconfig-prototype.h 785 2010-05-30 17:57:07Z cs $
+ */
+
+#ifndef __usbconfig_h_included__
+#define __usbconfig_h_included__
+
+#include "config.h"
+
+/*
+General Description:
+This file is an example configuration (with inline documentation) for the USB
+driver. It configures V-USB for USB D+ connected to Port D bit 2 (which is
+also hardware interrupt 0 on many devices) and USB D- to Port D bit 4. You may
+wire the lines to any other port, as long as D+ is also wired to INT0 (or any
+other hardware interrupt, as long as it is the highest level interrupt, see
+section at the end of this file).
+*/
+
+/* ---------------------------- Hardware Config ---------------------------- */
+
+#define USB_CFG_IOPORTNAME D
+/* This is the port where the USB bus is connected. When you configure it to
+ * "B", the registers PORTB, PINB and DDRB will be used.
+ */
+#define USB_CFG_DMINUS_BIT 3
+/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
+ * This may be any bit in the port.
+ */
+#define USB_CFG_DPLUS_BIT 2
+/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected.
+ * This may be any bit in the port. Please note that D+ must also be connected
+ * to interrupt pin INT0! [You can also use other interrupts, see section
+ * "Optional MCU Description" below, or you can connect D- to the interrupt, as
+ * it is required if you use the USB_COUNT_SOF feature. If you use D- for the
+ * interrupt, the USB interrupt will also be triggered at Start-Of-Frame
+ * markers every millisecond.]
+ */
+#define USB_CFG_CLOCK_KHZ (F_CPU/1000)
+/* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000,
+ * 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code
+ * require no crystal, they tolerate +/- 1% deviation from the nominal
+ * frequency. All other rates require a precision of 2000 ppm and thus a
+ * crystal!
+ * Since F_CPU should be defined to your actual clock rate anyway, you should
+ * not need to modify this setting.
+ */
+#define USB_CFG_CHECK_CRC 0
+/* Define this to 1 if you want that the driver checks integrity of incoming
+ * data packets (CRC checks). CRC checks cost quite a bit of code size and are
+ * currently only available for 18 MHz crystal clock. You must choose
+ * USB_CFG_CLOCK_KHZ = 18000 if you enable this option.
+ */
+
+/* ----------------------- Optional Hardware Config ------------------------ */
+
+/* #define USB_CFG_PULLUP_IOPORTNAME D */
+/* If you connect the 1.5k pullup resistor from D- to a port pin instead of
+ * V+, you can connect and disconnect the device from firmware by calling
+ * the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h).
+ * This constant defines the port on which the pullup resistor is connected.
+ */
+/* #define USB_CFG_PULLUP_BIT 4 */
+/* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined
+ * above) where the 1.5k pullup resistor is connected. See description
+ * above for details.
+ */
+
+/* --------------------------- Functional Range ---------------------------- */
+
+#define USB_CFG_HAVE_INTRIN_ENDPOINT 1
+/* Define this to 1 if you want to compile a version with two endpoints: The
+ * default control endpoint 0 and an interrupt-in endpoint (any other endpoint
+ * number).
+ */
+#define USB_CFG_HAVE_INTRIN_ENDPOINT3 1
+/* Define this to 1 if you want to compile a version with three endpoints: The
+ * default control endpoint 0, an interrupt-in endpoint 3 (or the number
+ * configured below) and a catch-all default interrupt-in endpoint as above.
+ * You must also define USB_CFG_HAVE_INTRIN_ENDPOINT to 1 for this feature.
+ */
+#define USB_CFG_EP3_NUMBER 3
+/* If the so-called endpoint 3 is used, it can now be configured to any other
+ * endpoint number (except 0) with this macro. Default if undefined is 3.
+ */
+/* #define USB_INITIAL_DATATOKEN USBPID_DATA1 */
+/* The above macro defines the startup condition for data toggling on the
+ * interrupt/bulk endpoints 1 and 3. Defaults to USBPID_DATA1.
+ * Since the token is toggled BEFORE sending any data, the first packet is
+ * sent with the oposite value of this configuration!
+ */
+#define USB_CFG_IMPLEMENT_HALT 0
+/* Define this to 1 if you also want to implement the ENDPOINT_HALT feature
+ * for endpoint 1 (interrupt endpoint). Although you may not need this feature,
+ * it is required by the standard. We have made it a config option because it
+ * bloats the code considerably.
+ */
+#define USB_CFG_SUPPRESS_INTR_CODE 0
+/* Define this to 1 if you want to declare interrupt-in endpoints, but don't
+ * want to send any data over them. If this macro is defined to 1, functions
+ * usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if
+ * you need the interrupt-in endpoints in order to comply to an interface
+ * (e.g. HID), but never want to send any data. This option saves a couple
+ * of bytes in flash memory and the transmit buffers in RAM.
+ */
+#define USB_CFG_INTR_POLL_INTERVAL 1
+/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
+ * interval. The value is in milliseconds and must not be less than 10 ms for
+ * low speed devices.
+ */
+#define USB_CFG_IS_SELF_POWERED 0
+/* Define this to 1 if the device has its own power supply. Set it to 0 if the
+ * device is powered from the USB bus.
+ */
+#define USB_CFG_MAX_BUS_POWER 500
+/* Set this variable to the maximum USB bus power consumption of your device.
+ * The value is in milliamperes. [It will be divided by two since USB
+ * communicates power requirements in units of 2 mA.]
+ */
+#define USB_CFG_IMPLEMENT_FN_WRITE 1
+/* Set this to 1 if you want usbFunctionWrite() to be called for control-out
+ * transfers. Set it to 0 if you don't need it and want to save a couple of
+ * bytes.
+ */
+#define USB_CFG_IMPLEMENT_FN_READ 0
+/* Set this to 1 if you need to send control replies which are generated
+ * "on the fly" when usbFunctionRead() is called. If you only want to send
+ * data from a static buffer, set it to 0 and return the data from
+ * usbFunctionSetup(). This saves a couple of bytes.
+ */
+#define USB_CFG_IMPLEMENT_FN_WRITEOUT 0
+/* Define this to 1 if you want to use interrupt-out (or bulk out) endpoints.
+ * You must implement the function usbFunctionWriteOut() which receives all
+ * interrupt/bulk data sent to any endpoint other than 0. The endpoint number
+ * can be found in 'usbRxToken'.
+ */
+#define USB_CFG_HAVE_FLOWCONTROL 0
+/* Define this to 1 if you want flowcontrol over USB data. See the definition
+ * of the macros usbDisableAllRequests() and usbEnableAllRequests() in
+ * usbdrv.h.
+ */
+#define USB_CFG_DRIVER_FLASH_PAGE 0
+/* If the device has more than 64 kBytes of flash, define this to the 64 k page
+ * where the driver's constants (descriptors) are located. Or in other words:
+ * Define this to 1 for boot loaders on the ATMega128.
+ */
+#define USB_CFG_LONG_TRANSFERS 0
+/* Define this to 1 if you want to send/receive blocks of more than 254 bytes
+ * in a single control-in or control-out transfer. Note that the capability
+ * for long transfers increases the driver size.
+ */
+/* #define USB_RX_USER_HOOK(data, len) if(usbRxToken == (uchar)USBPID_SETUP) blinkLED(); */
+/* This macro is a hook if you want to do unconventional things. If it is
+ * defined, it's inserted at the beginning of received message processing.
+ * If you eat the received message and don't want default processing to
+ * proceed, do a return after doing your things. One possible application
+ * (besides debugging) is to flash a status LED on each packet.
+ */
+/* #define USB_RESET_HOOK(resetStarts) if(!resetStarts){hadUsbReset();} */
+/* This macro is a hook if you need to know when an USB RESET occurs. It has
+ * one parameter which distinguishes between the start of RESET state and its
+ * end.
+ */
+/* #define USB_SET_ADDRESS_HOOK() hadAddressAssigned(); */
+/* This macro (if defined) is executed when a USB SET_ADDRESS request was
+ * received.
+ */
+#define USB_COUNT_SOF 1
+/* define this macro to 1 if you need the global variable "usbSofCount" which
+ * counts SOF packets. This feature requires that the hardware interrupt is
+ * connected to D- instead of D+.
+ */
+/* #ifdef __ASSEMBLER__
+ * macro myAssemblerMacro
+ * in YL, TCNT0
+ * sts timer0Snapshot, YL
+ * endm
+ * #endif
+ * #define USB_SOF_HOOK myAssemblerMacro
+ * This macro (if defined) is executed in the assembler module when a
+ * Start Of Frame condition is detected. It is recommended to define it to
+ * the name of an assembler macro which is defined here as well so that more
+ * than one assembler instruction can be used. The macro may use the register
+ * YL and modify SREG. If it lasts longer than a couple of cycles, USB messages
+ * immediately after an SOF pulse may be lost and must be retried by the host.
+ * What can you do with this hook? Since the SOF signal occurs exactly every
+ * 1 ms (unless the host is in sleep mode), you can use it to tune OSCCAL in
+ * designs running on the internal RC oscillator.
+ * Please note that Start Of Frame detection works only if D- is wired to the
+ * interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES!
+ */
+#define USB_CFG_CHECK_DATA_TOGGLING 0
+/* define this macro to 1 if you want to filter out duplicate data packets
+ * sent by the host. Duplicates occur only as a consequence of communication
+ * errors, when the host does not receive an ACK. Please note that you need to
+ * implement the filtering yourself in usbFunctionWriteOut() and
+ * usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable
+ * for each control- and out-endpoint to check for duplicate packets.
+ */
+#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH 0
+/* define this macro to 1 if you want the function usbMeasureFrameLength()
+ * compiled in. This function can be used to calibrate the AVR's RC oscillator.
+ */
+#define USB_USE_FAST_CRC 0
+/* The assembler module has two implementations for the CRC algorithm. One is
+ * faster, the other is smaller. This CRC routine is only used for transmitted
+ * messages where timing is not critical. The faster routine needs 31 cycles
+ * per byte while the smaller one needs 61 to 69 cycles. The faster routine
+ * may be worth the 32 bytes bigger code size if you transmit lots of data and
+ * run the AVR close to its limit.
+ */
+
+/* -------------------------- Device Description --------------------------- */
+
+#define USB_CFG_VENDOR_ID (VENDOR_ID & 0xFF), ((VENDOR_ID >> 8) & 0xFF)
+/* USB vendor ID for the device, low byte first. If you have registered your
+ * own Vendor ID, define it here. Otherwise you may use one of obdev's free
+ * shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules!
+ * *** IMPORTANT NOTE ***
+ * This template uses obdev's shared VID/PID pair for Vendor Class devices
+ * with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
+ * the implications!
+ */
+#define USB_CFG_DEVICE_ID (PRODUCT_ID & 0xFF), ((PRODUCT_ID >> 8) & 0xFF)
+/* This is the ID of the product, low byte first. It is interpreted in the
+ * scope of the vendor ID. If you have registered your own VID with usb.org
+ * or if you have licensed a PID from somebody else, define it here. Otherwise
+ * you may use one of obdev's free shared VID/PID pairs. See the file
+ * USB-IDs-for-free.txt for details!
+ * *** IMPORTANT NOTE ***
+ * This template uses obdev's shared VID/PID pair for Vendor Class devices
+ * with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
+ * the implications!
+ */
+#define USB_CFG_DEVICE_VERSION 0x00, 0x02
+/* Version number of the device: Minor number first, then major number.
+ */
+#define USB_CFG_VENDOR_NAME 'w', 'i', 'n', 'k', 'e', 'y', 'l', 'e', 's', 's', '.', 'k', 'r'
+#define USB_CFG_VENDOR_NAME_LEN 13
+/* These two values define the vendor name returned by the USB device. The name
+ * must be given as a list of characters under single quotes. The characters
+ * are interpreted as Unicode (UTF-16) entities.
+ * If you don't want a vendor name string, undefine these macros.
+ * ALWAYS define a vendor name containing your Internet domain name if you use
+ * obdev's free shared VID/PID pair. See the file USB-IDs-for-free.txt for
+ * details.
+ */
+#define USB_CFG_DEVICE_NAME 'p', 's', '2', 'a', 'v', 'r', 'G', 'B'
+#define USB_CFG_DEVICE_NAME_LEN 8
+/* Same as above for the device name. If you don't want a device name, undefine
+ * the macros. See the file USB-IDs-for-free.txt before you assign a name if
+ * you use a shared VID/PID.
+ */
+/*#define USB_CFG_SERIAL_NUMBER 'N', 'o', 'n', 'e' */
+/*#define USB_CFG_SERIAL_NUMBER_LEN 0 */
+/* Same as above for the serial number. If you don't want a serial number,
+ * undefine the macros.
+ * It may be useful to provide the serial number through other means than at
+ * compile time. See the section about descriptor properties below for how
+ * to fine tune control over USB descriptors such as the string descriptor
+ * for the serial number.
+ */
+#define USB_CFG_DEVICE_CLASS 0
+#define USB_CFG_DEVICE_SUBCLASS 0
+/* See USB specification if you want to conform to an existing device class.
+ * Class 0xff is "vendor specific".
+ */
+#define USB_CFG_INTERFACE_CLASS 3 /* HID */
+#define USB_CFG_INTERFACE_SUBCLASS 1 /* Boot */
+#define USB_CFG_INTERFACE_PROTOCOL 1 /* Keyboard */
+/* See USB specification if you want to conform to an existing device class or
+ * protocol. The following classes must be set at interface level:
+ * HID class is 3, no subclass and protocol required (but may be useful!)
+ * CDC class is 2, use subclass 2 and protocol 1 for ACM
+ */
+#define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH 0
+/* Define this to the length of the HID report descriptor, if you implement
+ * an HID device. Otherwise don't define it or define it to 0.
+ * If you use this define, you must add a PROGMEM character array named
+ * "usbHidReportDescriptor" to your code which contains the report descriptor.
+ * Don't forget to keep the array and this define in sync!
+ */
+
+/* #define USB_PUBLIC static */
+/* Use the define above if you #include usbdrv.c instead of linking against it.
+ * This technique saves a couple of bytes in flash memory.
+ */
+
+/* ------------------- Fine Control over USB Descriptors ------------------- */
+/* If you don't want to use the driver's default USB descriptors, you can
+ * provide our own. These can be provided as (1) fixed length static data in
+ * flash memory, (2) fixed length static data in RAM or (3) dynamically at
+ * runtime in the function usbFunctionDescriptor(). See usbdrv.h for more
+ * information about this function.
+ * Descriptor handling is configured through the descriptor's properties. If
+ * no properties are defined or if they are 0, the default descriptor is used.
+ * Possible properties are:
+ * + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched
+ * at runtime via usbFunctionDescriptor(). If the usbMsgPtr mechanism is
+ * used, the data is in FLASH by default. Add property USB_PROP_IS_RAM if
+ * you want RAM pointers.
+ * + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found
+ * in static memory is in RAM, not in flash memory.
+ * + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash),
+ * the driver must know the descriptor's length. The descriptor itself is
+ * found at the address of a well known identifier (see below).
+ * List of static descriptor names (must be declared PROGMEM if in flash):
+ * char usbDescriptorDevice[];
+ * char usbDescriptorConfiguration[];
+ * char usbDescriptorHidReport[];
+ * char usbDescriptorString0[];
+ * int usbDescriptorStringVendor[];
+ * int usbDescriptorStringDevice[];
+ * int usbDescriptorStringSerialNumber[];
+ * Other descriptors can't be provided statically, they must be provided
+ * dynamically at runtime.
+ *
+ * Descriptor properties are or-ed or added together, e.g.:
+ * #define USB_CFG_DESCR_PROPS_DEVICE (USB_PROP_IS_RAM | USB_PROP_LENGTH(18))
+ *
+ * The following descriptors are defined:
+ * USB_CFG_DESCR_PROPS_DEVICE
+ * USB_CFG_DESCR_PROPS_CONFIGURATION
+ * USB_CFG_DESCR_PROPS_STRINGS
+ * USB_CFG_DESCR_PROPS_STRING_0
+ * USB_CFG_DESCR_PROPS_STRING_VENDOR
+ * USB_CFG_DESCR_PROPS_STRING_PRODUCT
+ * USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER
+ * USB_CFG_DESCR_PROPS_HID
+ * USB_CFG_DESCR_PROPS_HID_REPORT
+ * USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver)
+ *
+ * Note about string descriptors: String descriptors are not just strings, they
+ * are Unicode strings prefixed with a 2 byte header. Example:
+ * int serialNumberDescriptor[] = {
+ * USB_STRING_DESCRIPTOR_HEADER(6),
+ * 'S', 'e', 'r', 'i', 'a', 'l'
+ * };
+ */
+
+#define USB_CFG_DESCR_PROPS_DEVICE 0
+#define USB_CFG_DESCR_PROPS_CONFIGURATION USB_PROP_IS_DYNAMIC
+//#define USB_CFG_DESCR_PROPS_CONFIGURATION 0
+#define USB_CFG_DESCR_PROPS_STRINGS 0
+#define USB_CFG_DESCR_PROPS_STRING_0 0
+#define USB_CFG_DESCR_PROPS_STRING_VENDOR 0
+#define USB_CFG_DESCR_PROPS_STRING_PRODUCT 0
+#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER 0
+#define USB_CFG_DESCR_PROPS_HID USB_PROP_IS_DYNAMIC
+//#define USB_CFG_DESCR_PROPS_HID 0
+#define USB_CFG_DESCR_PROPS_HID_REPORT USB_PROP_IS_DYNAMIC
+//#define USB_CFG_DESCR_PROPS_HID_REPORT 0
+#define USB_CFG_DESCR_PROPS_UNKNOWN 0
+
+#define usbMsgPtr_t unsigned short
+/* If usbMsgPtr_t is not defined, it defaults to 'uchar *'. We define it to
+ * a scalar type here because gcc generates slightly shorter code for scalar
+ * arithmetics than for pointer arithmetics. Remove this define for backward
+ * type compatibility or define it to an 8 bit type if you use data in RAM only
+ * and all RAM is below 256 bytes (tiny memory model in IAR CC).
+ */
+
+/* ----------------------- Optional MCU Description ------------------------ */
+
+/* The following configurations have working defaults in usbdrv.h. You
+ * usually don't need to set them explicitly. Only if you want to run
+ * the driver on a device which is not yet supported or with a compiler
+ * which is not fully supported (such as IAR C) or if you use a differnt
+ * interrupt than INT0, you may have to define some of these.
+ */
+/* #define USB_INTR_CFG MCUCR */
+/* #define USB_INTR_CFG_SET ((1 << ISC00) | (1 << ISC01)) */
+/* #define USB_INTR_CFG_CLR 0 */
+/* #define USB_INTR_ENABLE GIMSK */
+/* #define USB_INTR_ENABLE_BIT INT0 */
+/* #define USB_INTR_PENDING GIFR */
+/* #define USB_INTR_PENDING_BIT INTF0 */
+/* #define USB_INTR_VECTOR INT0_vect */
+
+/* Set INT1 for D- falling edge to count SOF */
+/* #define USB_INTR_CFG EICRA */
+#define USB_INTR_CFG_SET ((1 << ISC11) | (0 << ISC10))
+/* #define USB_INTR_CFG_CLR 0 */
+/* #define USB_INTR_ENABLE EIMSK */
+#define USB_INTR_ENABLE_BIT INT1
+/* #define USB_INTR_PENDING EIFR */
+#define USB_INTR_PENDING_BIT INTF1
+#define USB_INTR_VECTOR INT1_vect
+
+#endif /* __usbconfig_h_included__ */
diff --git a/keyboards/ymd96/keymaps/JJ50/keymap.c b/keyboards/ymd96/keymaps/JJ50/keymap.c
new file mode 100644
index 0000000000..f59950d445
--- /dev/null
+++ b/keyboards/ymd96/keymaps/JJ50/keymap.c
@@ -0,0 +1,96 @@
+/*
+Base Copyright 2017 Luiz Ribeiro <luizribeiro@gmail.com>
+Modified 2017 Andrew Novak <ndrw.nvk@gmail.com>
+Modified 2018 Wayne Jones (WarmCatUK) <waynekjones@gmail.com>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public LicensezZZ
+along with this program. If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#include "ymd96.h"
+#include "action_layer.h"
+#include "rgblight.h"
+
+#define ______ KC_TRNS
+#define _DEFLT 0
+#define _RAISE 1
+#define _LOWER 2
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+
+ /* Qwerty
+ * ,-----------------------------------------------------------------------------------.
+ * | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 0 | - | = |
+ * |------+------+------+------+------+------+------+------+------+------+------+------|
+ * | Tab | Q | W | E | R | T | Y | U | I | O | P | Bksp |
+ * |------+------+------+------+------+------+------+------+------+------+------+------|
+ * | Esc | A | S | D | F | G | H | J | K | L | ; | " |
+ * |------+------+------+------+------+------+------+------+------+------+------+------|
+ * | Shift| Z | X | C | V | B | N | M | , | . | / |Enter |
+ * |------+------+------+------+------+------+------+------+------+------+------+------|
+ * | | Ctrl | Alt | GUI |Lower | Space |Raise | Left | Down | Up |Right |
+ * `-----------------------------------------------------------------------------------'
+ */
+ [_DEFLT] = KEYMAP_JJ50( \
+ KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, \
+ KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_BSPC, \
+ KC_ESC, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, \
+ KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, SFT_T(KC_ENT),\
+ _______, KC_LCTL, KC_LALT, KC_LGUI, MO(_LOWER), KC_SPC,KC_SPC, MO(_RAISE),KC_LEFT, KC_DOWN, KC_UP, KC_RGHT \
+ ),
+
+
+ /* Raise
+ * ,-----------------------------------------------------------------------------------.
+ * | F1 | F2 | F3 | F4 | F5 | F6 | F7 | F8 | F9 | F10 | F11 | F12 |
+ * |------+------+------+------+------+------+------+------+------+------+------+------|
+ * | ` | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 0 | Del |
+ * |------+------+------+------+------+------+------+------+------+------+------+------|
+ * | | | | | | | | | | [ | ] | \ |
+ * |------+------+------+------+------+------+------+------+------+------+------+------|
+ * | | | | | | | |ISO # |ISO / | PUP | PDN | |
+ * |------+------+------+------+------+------+------+------+------+------+------+------|
+ * | | | | | | | | Next | Vol- | Vol+ | Play |
+ * `-----------------------------------------------------------------------------------'
+ */
+ [_RAISE] = KEYMAP_JJ50( \
+ KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, \
+ KC_GRV, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_DEL, \
+ _______, _______, _______, _______, _______, _______, _______, _______, _______, KC_LBRC, KC_RBRC, KC_BSLS, \
+ _______, _______, _______, _______, _______, _______, _______, KC_NUHS, KC_NUBS, KC_PGUP, KC_PGDN, _______, \
+ _______, _______, _______, _______, _______, _______, _______, _______, KC_MNXT, KC_VOLD, KC_VOLU, KC_MPLY \
+ ),
+
+
+ /* Lower
+ * ,-----------------------------------------------------------------------------------.
+ * | F1 | F2 | F3 | F4 | F5 | F6 | F7 | F8 | F9 | F10 | F11 | F12 |
+ * |------+------+------+------+------+------+------+------+------+------+------+------|
+ * | ~ | ! | @ | # | $ | % | ^ | & | * | ( | ) | Del |
+ * |------+------+------+------+------+------+------+------+------+------+------+------|
+ * | | | | | | | | | | { | } | | |
+ * |------+------+------+------+------+------+------+------+------+------+------+------|
+ * | | | | | | | |ISO ~ |ISO | | HOM | END | |
+ * |------+------+------+------+------+------+------+------+------+------+------+------|
+ * | | | | | | | | Next | Vol- | Vol+ | Play |
+ * `-----------------------------------------------------------------------------------'
+ */
+ [_LOWER] = KEYMAP_JJ50( \
+ KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, \
+ KC_TILD, KC_EXLM, KC_AT, KC_HASH, KC_DLR, KC_PERC, KC_CIRC, KC_AMPR, KC_ASTR, KC_LPRN, KC_RPRN, KC_DEL, \
+ _______, _______, _______, _______, _______, _______, _______, _______, _______, KC_LCBR, KC_RCBR, KC_PIPE, \
+ _______, _______, _______, _______, _______, _______, _______,S(KC_NUHS),S(KC_NUBS),KC_HOME, KC_END, _______, \
+ _______, _______, _______, _______, _______, _______, _______, _______, KC_MNXT, KC_VOLD, KC_VOLU, KC_MPLY \
+ )
+
+};
diff --git a/keyboards/ymd96/ymd96.h b/keyboards/ymd96/ymd96.h
index 8a420ab5c1..541ebeb191 100644
--- a/keyboards/ymd96/ymd96.h
+++ b/keyboards/ymd96/ymd96.h
@@ -41,6 +41,19 @@ along with this program. If not, see <http://www.gnu.org/licenses/>.
{ K700, K701, K702, K703, K704, K705, K706, KC_NO, K708, K709, K710, K711, K712, K713, K714 } \
}
+#define KEYMAP_JJ50( \
+K011, K010, K009, K008, K004, K005, K006, K007, K003, K002, K201, K000, \
+K111, K110, K109, K108, K104, K105, K106, K107, K103, K102, K001, K100, \
+K211, K210, K209, K208, K204, K205, K206, K207, K203, K202, K101, K200, \
+K311, K310, K309, K308, K304, K305, K306, K307, K303, K302, K301, K300, \
+K411, K410, K409, K408, K404, K405, K406, K407, K403, K402, K401, K400 \
+) { \
+{ K100, K001, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, }, \
+{ K200, K101, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, }, \
+{ K000, K201, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, }, \
+{ K300, K301, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, }, \
+{ K400, K401, K402, K403, K404, K405, K406, K407, K408, K409, K410, K411 }, \
+}
#endif